My Weblog

Just another WordPress.com weblog

Mereset Wifi Senao NOC-3220 /EOC-3220

Mereset Wifi Senao NOC-3220 /EOC-3220

Wifi merk senao outdor dengan type EOC-3220,atau yang sejenis yang tidak dilengkapi tombol reset pada hardwarenya, cukup merepotkan kalau terjadi hang atau ada masalah konfigurasi atau administrator wifi lupa akan ip untuk konfigurasi, satu-satunya jalan hanya menggunakan port RS-232 (COM 1), nah ini deh caranya.

1. Cari kabel modem serial dengan connector RS-232 female pada dua sisinya
2. Buka baut yang menutup port serial pada wifi anda dan colokkan connector yang anda miliki dan disatu sisi colokkan ke port com1 pc anda
3. Gunakan menu Hyper terminal bagi anda pengguna windows 98, 2000, xp dengan cara klik Start –> Program —> Accessories –> Communications –>HyperTerminal
4. Buat koneksi baru dan isi dengan nama terserah anda
5. Pilih port COM sesuaikan dengan port com pc yang anda gunakan
6. Set baud rate pada 38400, data bits 8, parity none , stop bits 1 , flow control none
7. setelah terbuka jendela ketik “OK” tekan enter
8. tunggu beberapa saat sampai muncul tanda # pada jendela terminal
9. setelah muncul # ketik flash reset tekan enter
10. Setelah itu ketik reboot dan tekan enter.
11. Kalau tidak ada kesalahan maka konfigurasi wifi senao anda kembali seperti saat anda baru beli dari toko.

# flash reset

resetDefault()
# reboot

The system is going down NOW !!
Sending SIGTERM to all processes.
Terminated
[2] + Terminated                 reload
[1] + Terminated                 webs
# Sending Please stand by while rebooting the system.
Restarting system.
Shutdown network interface
wlan0:===>
br0: port 2(wlan0) entering disabled state
eth0:===>
br0: port 1(eth0) entering disabled state
br0:===>
Enable Watch Dog to Reset whole system

UART1 output test ok
Uart init
mfid=000000c2 devid=000022a8
Uncompressing Linux… done, booting the kernel.
done decompressing kernel.
early printk enabled
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initial ramdisk at: 0×801bd000 (5529600 bytes)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram console=0 ramdisk_start=0 single
Calibrating delay loop… 178.99 BogoMIPS
Memory: 8792k/16384k available (1613k kernel code, 7592k reserved, 5500k data, 5
2k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
check_wait… unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Serial driver version 6.02 (2003-03-12) with no serial options enabled
ttyS00 at 0×00c3 (irq = 3) is a rtl_uart1
state->flags=00000000
Realtek GPIO Driver for Flash Reload Default
block: 64 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 7000K size 1024 blocksize
PPP generic driver version 2.4.1
PPP MPPE Compression module registered
RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
Found 1 x 4M Byte MXIC MX29LV320AB at 0xbe000000
RTL8185 driver version 1.12 (2007-01-26)
8186NIC Ethernet driver v0.0.7 (Nov 8, 2006)
eth0: RTL8186-NIC at 0xbd200000, 00:01:02:03:04:05, IRQ 4
eth1: RTL8186-NIC at 0xbd300000, 04:05:06:07:08:09, IRQ 5
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 204 8)
rtl8186_crypto_init()…
rtl8186_crypto: IPSec status(RTL8186_IPSCFR) = B
rtl8186_crypto: IPSec status(RTL8186_IPSCTR) = 2027202
ipsec_3des_init(alg_type=15 alg_id=3 name=3des): ret=0
ipsec_aes_init(alg_type=15 alg_id=12 name=aes): ret=0
ipsec_md5_init(alg_type=14 alg_id=2 name=md5): ret=0
ipsec_null_init(alg_type=15 alg_id=11 name=null): ret=0
ipsec_sha1_init(alg_type=14 alg_id=3 name=sha1): ret=0
ip_conntrack version 2.1 (128 buckets, 1024 max) – 312 bytes per conntrack
PPTP netfilter connection tracking: regi
PPTP netfilter NAT helper: registered
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 5400 blocks [1 disk] into ram disk… done.
Freeing initrd memory: 5400k freed
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 52k freed
mount /proc file system ok!
serial console detected.  Disabling virtual terminals.
init started:  BusyBox v1.00-pre8 (2005.09.16-02
BusyBox v1.00-pre8 (2005.09.16-02:21+0000) Built-in shell (ash)
Enter ‘help’ for a list of built-in commands.

Initialize wlan0 interface
Setup BRIDGE interface
killall: syslogd: no process killed
killall: klogd: no process killed
SIOCGIFFLAGS: No such device
bridge br0 doesn’t exist; can’t delete it
Setup bridge…
device eth0 entered promiscuous mode
eth0:phy is 8201
SIOCDELRT: No such process
device wlan0 entered promiscuous mode
SIOCDELRT: No such process
br0: port 2(wlan0) entering listening state
br0: port 1(eth0) entering listening state
br0: port 2(wlan0) entering learning state
br0: port 2(wlan0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering learning state
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
SIOCDELRT: No such process
SIOCDELRT: No such process
SIOCDELRT: No such process
Auto-Discovery (ver 1.01)
killall: snmpd: no process killed
publicprivatekillall: snmptrapd: no process killed
killall: nuttcp: no proc
#

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: